My physical cards dont work. Possibly wrong setup when writing data onto the stripe??

[Ontour]

Hi together
I was trying to write some 101 dumps with my MCR200 and I am facing some issues. I’m writing the magnetic stripe only..
I was trying several different tools like Cardpeek, TheJerm, Exeba, MSRX & MAgstripcard reader/writer Utility. Most oft he tools did not work because some did not recognize my MCR200, Exeba and TheJerm recognized it but did not communicate properly and frooze.
Magstrip ist he only which is working fine and is the one i used here, however it seems to be very basic, there is not much to configure and reading as well as writing seems to be working fine.
When reading a card, i get the data exactly as it is shown below, meaning there is nothing like a start sentinel like „%“ but simply the naked string. So when writning my dump data i used the same format. I used:
Track1: B0XXXXXXXXXX69423^MAUER/STEFFEN^22071010000000000277689382573383000000
Track2: 0XXXXXXXXXXX69423=2207101277689382573
I was writing that onto my card and swiped it through a POS @ McDonnalds. The POS device said „read error“
I then went back home and added sentinel and stop sign like:
Track1: %B0XXXXXXXXXX69423^MAUER/STEFFEN^22071010000000000277689382573383000000?
Track2: ;0XXXXXXXXXXX69423=2207101277689382573?
Additionally i made a second card, similar to the above, including sentinels but i also substituted „=“ in track 2 with „‘ “
The sign `did not make much sense to me but i tried it because i have seen one of my cards showing track 2 like that after i was reading it, so i gave it a try.
Those 2 cards did not show „read error“ this time when swiped through the POS but they were showing something like „can not proceed“. POS and shop was a different model compared to the first one.
I cant see what i did wrong here, so i would be happy if someone could give me advice.
I hope my language was good enough to make you understand what i am trying to explain…
Thx and all the best,
bitmain
my config:
https://www1.xup.in/exec/ximg.php?fid=76427767
https://www1.xup.in/exec/ximg.php?fid=11041658

[Paul244R]

What’s ur telegram? I‘ll help u bro

[silentswisdom]

vzsa, same problem telegram me at Realdealexpensive

[jamesjojo1x]

Bro i need help too with mycard and tapn pay please. I have a track 2 that someone posted on this forum that approved for 200 bux I wanna know how to use it right plz help

[Jackyzhang]

Originally Posted by ForcedBin3000

Bro i need help too with mycard and tapn pay please. I have a track 2 that someone posted on this forum that approved for 200 bux I wanna know how to use it right plz help

Approved for $200 where?
Mycard formerly called airpay is shit now
Your best bet is DDA custom APK, that goes for $1000 and works only with MasterCard for NFC tap and pay

[screamix]

Your msr software should automatically add the symbols like % ; ?
and you must have = in track 2
but I have no experience with mcr200.
Why does your card # start with 0 ? Your track1 shown above looks incredibly long too. I would leave track 1 off. Just put "B" no quotes and thats it. Track 1 isn't needed at most places, depends on the store.

[coffeman]

did you get it working?

[Greygooseman]

Bro can I contact you? i want to know about mycard news

[Osiris]

Use MSRE206 2.8
https://msre206.software.informer.com/amp/2.8/